Radiant Floor Heating with Crete Heat Panels

Posted on April 9, 2011 by Rob

Radiant Floor Heating from Barn World with the Crete-Heat Floor Panel System

The easy use and install Electric Boilers for Radiant Floor Heating is designed to be used with PEX Tubing and the Crete Heat Insulated Floor Panels. This system is designed specifically for installation in poured concrete basement and garage slabs that are well insulated below and around the outside edge of the slab. Use these hydronic heating kits to heat up to 900 or 1000-1800 square feet of single-zone basement, garage, greenhouse, or home addition. Radiant-Made-Simple Radiant Heat Systems provide an energy-efficient (approaching 99%) solution for concrete floor heating.

CHOOSE YOUR RMS MODEL ACCORDING TO THE SPACE YOU WISH TO HEAT IN YOUR BASEMENT OR GARAGE, AND YOUR ELECTRICAL REQUIREMENTS

Square Feet	RMS Model	Loops	BTU/h
350 to 600	RMS-7	2	23890
610 to 900	RMS-7	2	23890
910 to 1200	RMS-11	3	37540
1210 to 1500	RMS-11	4	37540
1510 to 1800	RMS-11	5	37540

ELECTRIC SERVICE REQUIREMENTS
MODEL	AC VOLTAGE	HEATER AMPS	BREAKER
RMS-7	220/240	29	40 AMPS
RMS-11	220/240	46	60 AMPS

HAVE AN AREA LARGER THAN 1,800 SQUARE FEET?
Areas larger than 1800 square feet should be subdivided and served with two or more RMS units sized for each area.

EXAMPLE #1: A 2500 square foot basement could be treated as two, 1,250 square foot areas each served by one RMS-11 boiler having 4 loops each.

EXAMPLE #2: Two temperature zones are desired in the 2,500 square foot basement, one 760 square foot zone could be served by one RMS-7 boiler with 2 – 300 foot loops, and the remaining 1,760 square foot area served by one RMS-11 heater with 5 – 300 foot loops. (Thermal isolation is required)

THE BASICS OF RADIANT FLOOR HEAT

PEX Tubing

PEX Oxygen barrier tubing installs with Radiant Heat system on 2” insulation foam board. This Radiant Made Simple Radiant Floor Tubing Kit works with Radiant Made Simple Radiant Heat systems. Requires .92 gallons of RV antifreeze per 100 feet of tubing. 300′ X 1/2″ PEX Oxygen barrier tubing installs with Radiant Heat system on insulating foam board. Tube bends help make the transition from tubing in concrete to the manifolds. Allow 1 linear foot of tubing for 1 square foot of space to be heated. Order 1 each 300’ Loop Kit per 300 square feet of space to be heated.

Crete-Heat Insulated Floor Panel System – 1″ Thick

Insulation Benefits

Cuts radiant system install time by as much as 2/3
Designed to hold tube securely in place with wider fasteners
2 sizes are available for both new construction and retrofitting existing buildings
UV Protected Packaging for outdoor storage

Ready For Concrete

The Crete-Heat Insulated Floor Panel System, is an easily assembled modular board insulation, vapor barrier, and radiant tube holding grid that allows for easy installation of hydronic radiant floor heating systems in basements, garages, main floor slabs on grade and above grade installations where concrete or Gyp-Crete is normally used. For basements, a ‘light weight’ concrete (sand instead of pea gravel) may be used in 1-1/2″ thickness. Uses 1/2″ tubing. Total thickness is 1-7/8″. This Product is sold by the bag, each containing 12 panels and covering 96 square feet. To determine your total square footage, divide your total square footage by 96 for the number of bags needed.

2″ Thick Crete-Heat Insulated Floor Panel

insulated floor panel with pex tubing installed

These panels provide 2″ of insulation while the PEX knobs add approximately 7/8″ more for an overall height of 2-7/8″.

Crete Heat Specifications

2″ of insulating thickness
the vapor barrier on each panel
overall thickness is 2-7/8″
Ships in UV and weather-proof packaging – see below

insulated floor panels in bags ready to ship

Ready For Concrete
These panels are easily assembled and have overlapping lips for securing to each other and holding while concrete is poured. It simplifies the installation of PEX tubing and also secures it from moving during the pour. Each panel is made with a vapor barrier and is great for heating systems in basements, garages, and main floor slabs on grade and above grade installations where concrete or gypcrete is normally used.

Each panel board size is 25″ x 49″ with an effective insulating area of 24″ x 48″. Each interlocking panel covers up to 8 square feet with knobs to accommodate 3/8″ up to 1″ sized PEX. A 10-mil polystyrene film provides the vapor barrier.

Electric Boilers for Floor HeatThe electric boilers are specifically designed for use with radiant heating systems and provide energy-efficient heat in a do-it-yourself package. You can heat single or multiple zones and typical uses are in basements, garages, and anywhere a new slab is being poured.

They have multiple manifolds for controlling individual zones and are a simple and efficient means of providing warmth throughout the slab.

Let us know if we can help with your next Radiant Floor heating project!Barn World – (720) 238-2190 BarnWorld.com

Calf Warmer and calving pen from Barn World

Posted on April 9, 2011 by Rob

Now is the time to buy a calf warmer, calving pen, and maternity pen. This has been a brutally cold winter all across the country – where’s that global warming? Calves are being born now. Make sure you are ready with a calf warmer in proper working condition.

Our calf warmers offer the best possible care for a newborn calf. BarnWorld.com sells calf warmers made of long-lasting polyethylene for durability and easy cleaning. The calf warmer creates the perfect closed environment for a newborn during those first critical hours after birth. The heater, located in a separate enclosure at the rear of the calf warmer, uses a circulating fan and automatic shutoff thermostat to regulate air flow and keep vulnerable newborn calves warm. The inside of the calf warmer has enough room so the calf can either stand or lie down. The calf’s instinctive identity scent is not removed, so waiting mothers will reclaim their rejuvenated infants at once.

BarnWorld.com also offers replacement heaters for calf warmers. Make sure yours is in good working order or get one of our replacements before you need it. Don’t end up with your calves in the cab of your truck to keep warm.

Now is also the time to think about getting a calving pen or maternity pen. BarnWorld.com carries two types of calving pens to help you save calves from difficult heifers. All sides of the square calving pen have an in-and-out swing gate and latch for easy access from any direction. The circular maternity pen has a confinement pen and nursing panels on two sides. You can get an optional self-catching headgate with either model.

Be ready for calving season. Order your calf warmers, calf warmer heaters, and calving pens now. Call us for shipping quotes at 720-238-2190.

Calf warmers provide essential protection from the elements when your calf is most vulnerable. Mother Nature doesn’t care that it’s calf season and subjects your newborns to the harshness of winter right after birth.

Now is the time to buy a calf warmer to protect them and help them make a quick recovery right after experiencing birth into their brave new world. Make sure you’re ready to protect them and that your young ones can recover from the birthing process out in the cold pasture.

Our calf warmers offer the best possible care for a newborn calf. They’re made of long-lasting polyethylene for durability and easy cleaning and create the perfect closed environment for a newborn during those first critical hours after birth.

The heater is located in a separate enclosure at the rear of the calf warmer and uses a circulating fan and automatic shutoff thermostat to regulate the airflow and keep vulnerable newborn calves warm. The inside has enough room so the animals can either stand or lie down during recovery. The calf’s instinctive identity scent is not removed, so waiting mothers will reclaim their rejuvenated infants at once.

: Polyethylene Calf Warmer

You can also buy the heater separately if a replacement is necessary. It is the heart of the warmer and needs to be functioning properly to protect your animal. Make sure yours is in good working order or get an extra one to have on hand in case you need a replacement quickly. You don’t want to end up trying to keep your newborns warm in the cab of your truck!

Now is also the time to think about getting prepared with a calving pen or maternity pen. There are two types of pens to help you sort calves from difficult heifers. All sides of the square calving pens have an in-and-out swing gate and latch for easy access from any direction. The circular maternity pen has a confinement area that includes nursing panels on two sides. You can get an optional self-catching head-gate with either model to hold them safely.

: circular maternity calving pen

Be ready for calving season and the supplies and equipment you need ahead of the season. Call BarnWorld.com for quotes that include shipping directly to your ranch at 720-238-2190.

Livestock Waterers from Barn World

Posted on April 9, 2011 by Rob

Barn World Post: Livestock Waterers

Livestock waterers are important for keeping your animals for health and weight gain. Barn World has a wide selection oflivestock waters for all you animal waterer needs.

: BIGspring – ENERGY FREE WATERER – 60 Gallon with heat

The large 60 gallon Big Spring Waterer is a constant-flow watering system ideally suited for free-stall dairy operations and large feedlots. If you raise beef or dairy cows, the BIGspring model is perfect to fit your needs.

: LilSpring WATERER – Double-Sided 6 GAL (with heat in GREEN)

Smaller waterers in the Lil Spring waterer models are ideal for small animals or groups of small animals — such as goats, llamas, ponies, horses, and many others. Lil’Spring models can accomodate multiple pens by installing them in a split-fence application. We offer them as single or double sided waterer.

: MiraFount – ENERGY FREE WATERER – 4 HOLE Removable

Our Energy-Free Waterers:

E-Founts are the most economical electric heat waterers available today. The E-Fount is equipped with a 50 watt heat element and thermostat. E-Founts only require 4 kilowatts of electricity during a week of -25 degree F temperatures. This model is ideally suited to operations with just a few animals drinking infrequently or if extreme cold weather conditions are persistent.

We also offer the MiraFount models which are patterned after their first energy-free livestock watering systems, built more than 30 years ago. These small. medium and large capacity watering systems are ideal for beef operations, dairy herds and other livestock.

: Hog and Pig Waterers

Hog Waterers

We also have utility Hog Waterers in 80 and 35 gallon sizes. The hog waterer is:

Made of 100% non-porous polyethylene – will not rust, rot or corrode.

Confinement pen acids have no effect – waterers last and last.

Quick and easy cleaning – no pans or shields to remove from drinker trough.

Big hogs drink with ease from 18” wide x 17” high x 9 fl” deep drinkers.

Trough height from floor is 6”, so little pigs drink easily.

No cracks, corners or crevices to collect sediment or bacteria.

Each drinker has a drain plug, so washing and flushing is fast, simple and complete.

One dependable float and valve handles both drinkers.

Heavy steel-plated chew guard protects trough lip.

Gallon capacity calibrations molded into tank wall.

Float and valve completely protected from hogs.

Remember to keep your animals healthy with a animal waterer from Barn World. Visit BarnWorld.com for all your livestock equipment needs.

Barn World Calf Warmer and Calving Pens

Posted on March 2, 2011 by Rob

Be ready for calving season. Order your calf warmers, calf warmer heaters, and calving pens now. Call us for shipping quotes at 720-238-2190.

Now is the time to buy a calf warmer, calving pen, and maternity pen. This has been a brutally cold winter all across the country. Calves are being born now. Make sure you are ready with a calf warmer in proper working condition.

: Polyethylene Calf Warmer

: circular maternity calving pen

Be ready for calving season. Order your calf warmers, calf warmer heaters, and calving pens now. Call BarnWorld.com for shipping quotes at 720-238-2190.

Radiant Floor Heating

Posted on February 25, 2011 by Rob

Radiant Floor Heat with Crete-Heat Floor Panels and DIY Heaters

Installing a radiant heating system in a new slab doesn’t have to be complicated or expensive. These systems provide very economical and efficient heat to large areas in a quiet and cost-effective manner.

PRICE REDUCED !! – You simply cannot afford to install radiant floor heating without this product!

You certainly cannot afford the energy lost into the ground!

Radiant Floor Insulated Panels

These 2′ x 4′ panels are available in 1″, 2″ and 3″ thickness for varying R-values. Each panel has a vapor barrier and the edges overlap to interlock together for ease of installation. The overlaps also minimize movement when installing the PEX and pouring the concrete.

The knobs on each panel hold the PEX securely in place and allow you to walk directly on them to push the PEX into place. They add approximately 7/8″ of an inch to the listed panel thickness. As and example, the 2″ panels offer 2″ of insulating thickness and the knobs add another 7/8″ on top of that for an overall thickness of 2-7/8″.

Electric Heaters for Radiant Floor Heat

CHOOSE YOUR RMS MODEL ACCORDING TO THE SPACE YOU WISH TO HEAT IN YOUR BASEMENT OR GARAGE, AND YOUR ELECTRICAL REQUIREMENTS

Square Feet	RMS Model	Loops	BTU/h
350 to 600	RMS-7	2	23890
610 to 900	RMS-7	2	23890
910 to 1200	RMS-11	3	37540
1210 to 1500	RMS-11	4	37540
1510 to 1800	RMS-11	5	37540

ELECTRIC SERVICE REQUIREMENTS
MODEL	AC VOLTAGE	HEATER AMPS	BREAKER
RMS-7	220/240	29	40 AMPS
RMS-11	220/240	46	60 AMPS

HAVE AREAS LARGER THAN 1800 SQUARE FEET? NO PROBLEM
Areas larger than 1800 square feet should be subdivided and served with two or more RMS units sized for each area.

EXAMPLE #1: A 2500 square foot basement could be treated as two 1250 square foot areas each served by one RMS11 having 4 loops each.

EXAMPLE #2: Two temperature zones are desired in the 2500 square foot basement, one 760 square foot zone could be served by one RMS7 with 2 300 foot loops, and the remaining 1760 square foot area served by one RMS11 with 5 300 foot loops. (Thermal isolation is required)

300’ Loop Kit – PEX Radiant Floor Tubing Kit

PEX Oxygen barrier tubing installs with Radiant Heat system on 2” insulation foam board. This Radiant Made Simple Radiant Floor Tubing Kit works with Radiant Made Simple Radiant Heat systems. Requires .92 gallons of RV antifreeze per 100 feet of tubing. 300′ X 1/2″ PEX Oxygen barrier tubing installs with Radiant Heat system on insulating foam board. Tube bends help make the transition from tubing in concrete to the manifolds. Allow 1 linear foot of tubing for 1 square foot of space to be heated. Order a 300’ Loop Kit per 300 square feet of space to be heated.

Radiant Heat Floor Panel Benefits

Cuts installation time by as much as 2/3 – no stapling and nicking PEX and no extra vapor barrier to buy and install
The knows hold the PEX tubing securely in place
There are multiple R-ratings available
UV Protected Packaging for outdoor storage

Ready For Concrete
The Crete-Heat^TMInsulated Floor Panel System, is an easily assembled modular board insulation, vapor barrier, and radiant tube holding grid that allows for simplified installation of hydronic radiant floor heating systems in basements, garages, main floor slab on grade and above grade installations where concrete or gypcrete is normally used. For basements, a ‘light weight’ concrete (sand instead of pea gravel) may be used in 1-1/2″ thickness. Uses 1/2″ tubing. Total thickness is 1-7/8″

Crete-Heat Insulated Floor Panel System – 1″ Black Bag

This Product is SOLD BY THE BAG – 12 PIECES PER BAG

The 1″ thick panels ship in a black bag and each bag covers 96 Sq Ft. To determine the number of bags needed, divide your total square footage by 96 and round up to the next whole number.

Crete-Heat Insulated Floor Panel System – 2″ Green Bag

Cuts radiant system install time by as much as 2/3
Designed to hold tube securely in place with wider fasteners
2 sizes are available for both new construction and retrofitting existing buildings
UV Protected Packaging for outdoor storage

Ready For Concrete
The Crete-Heat Insulated Floor Panel System, is an easily assembled modular board insulation, vapor barrier, and radiant tube holding grid that allows for simplified installation of hydronic radiant floor heating systems in basements, and garages, main floor slab on grade and above grade installations where concrete or gypcrete is normally used. The Crete-Heat Insulated Floor Panel System is 2 7/8″ overall in thickness, with 2″ of solid EPS foam providing an R-10. The panel board size is 25″ x 49″ and the effective area is 24″ x 48″.

Our retrofit of over grade panel provides 2 1/8″ overall in thickness, with 1″ of solid EPS foam providing and R-6 with a 23 dB sound reduction knob on the lower surface. Each interlocking panel covers up to 8 square feet with fasteners for 1/2″ and 5/8″ radiant tubing. A 10-mil polystyrene film provides the vapor barrier.

This Product is SOLD BY THE BAG – 8 PIECES PER BAG
EACH 2″ Green Bag covers 64 Sq Ft. Determine your total square footage and divide by 64 for the total BAGS needed.

Radiant Floor Heaters

These Electric Boilers provide an energy-efficient, Do-It-Yourself solution, for heating a single zone: basements, garages, home additions, greenhouse or remodeling projects. Energy efficiency approaches 99%!

RMS-7 – Radiant Made Simple Radiant Heat System – 7 kW, 23,890 BTU Electric Heater, 240 Volts A/C, 40 Amp.
Radiant Made Simple Radiant Heat Systems provides an energy-efficient, Do-It-Yourself solution, for heating a single zone: basements, garages, home additions, greenhouse or remodeling projects. This 230V, 40 Amp product provides everything you need to install radiant floor heating. Efficiency approaches 99%.

For help or a quote with shipping to your address, please contact Barn World today!

Barn World Customer Service – (720) 238-2190 – Sales@BarnWorld.com

Cattle guard choices and designs

Posted on February 25, 2011 by Rob

There are many different choices when selecting a cattle guard for your livestock containment needs. They may be called by various names (Texas gates, animal guards, cattle grids, cow guards etc.) but they all are built around the same great idea: provide a visual deterrent coupled with a physical barrier to keep livestock from crossing. This provides containment for your herd while allowing vehicle crossings without a gate!

Rated Cattle Guards

The rated cattle guards are designed for highway use and certified to meet the specifications needed for State and Federal requirements such as DOT installations. They’re design and construction is certified by an engineer to meet the required load ratings.

Cattle Guard Load Ratings

H-15 (12 tons per axle)

H-20 (16 tons per axle)

U-54 (25 tons per axle)

U-80 (30 tons per axle)

They’re available in flat top rail designs in a powder-coated finish as well as the more economical round top rail design that’s coated in a tough enamel. They will provide years of rugged service in heavy-duty high traffic public areas.

These are also available for private driveways such as farms and ranch applications. This design in much more economical and we estimate the load-carry capacity at 12 tons per axle. That’s plenty for most driveway use and easily support fully-loaded semis. We call them ‘Standard Cattle Guards.’

Cattle Guard – Standard

Barn World’s private-use, economical choice of the standard guard is a very popular option for driveways. They are made with NEW 3″ Schedule 40 steel with the same construction technique used on the rated guards.

All of the round top rail designs may be ordered with optional wings, integral box, or removable box.

ATV cattle guards

are unique in the industry. They’re built for quick and easy installation and attach directly to your fence line without the need for a foundation. We recommend providing sufficient drainage to the area and keeping it clear of overgrowth from surrounding vegetation. Other than that, simply set in your fence line, attach the fencing to the uprights and you’re done!

Options

All cattle guards may be fitted with plow strips that allow plows to cross over the guard with minimal interference and wear.

All round top rail designs may be outfitted with a removable box for easier cleaning as an option.

They may also have a steel skirt welded to the perimeter which allows it to be placed directly on the ground without the need for a foundation.

Barn World has a cattle guard to meet your needs. Please call us (720) 238-2190 with your questions and to obtain shipping quotes. We can also provide professional bid packages for large company, military, and government programs and carry a large selection for all of your livestock equipment needs.

Animal vacuums and livestock blowers

Posted on February 25, 2011 by Rob

Barn World features a large selection of livestock vacuums and blowers and even industrial vacuums. All of your animal blower and animal vacuum need can be met at www.BarnWorld.com.

Cattle Vacuums

Industrial Vacuums

* All units are available in 220 volt

Ideal For:

Equestrian
Agricultural
Industrial
Manufacturing
Commercial
Recreational
Health Care
Hospitality
Educational

Features:

Four models/capacities
Large industrial capacity filter
Heavy-duty vacuum power
90% efficiency at .3 micron particles
Quick and easy operation
Rugged 18-gauge steel construction
Double vac and blower power
CSA & UL approved components

12 Gallon 12 G00 Vac-N-Groom

Capacity:	12 gal.
Turbines:	1
RPM:	22470
AMPS:	9.4
Volts:	120
Cycle:	60
Construction:	18-Gauge Steel
Warranty:	1 year
Hose:	15 ft. / 1-1/2″ Diam.
Air Flow:	119.3
Water Lift:	100″
Motor Type:	Lamb 923
Noise Level:	OSHA Approved

Available on casters or on cart.

20 Gallon 20 G00 Vac-N-Groom

Capacity:	20 gal.
Turbines:	1
RPM:	22470
AMPS:	9.4
Volts:	120
Cycle:	60
Construction:	18-Gauge Steel
Warranty:	1 year
Hose:	15 ft. / 1-1/2″ Diam.
Air Flow:	119.3
Water Lift:	100″
Motor Type:	Lamb 923
Noise Level:	OSHA Approved

Available on casters or on cart.

30 Gallon 30 G 00 Turbine-Twin

Capacity:	30 gal.
Turbines:	2
RPM:	22470
AMPS:	17
Volts:	120
Cycle:	60
Construction:	18-Gauge Steel
Warranty:	1 year
Hose:	Two 15 ft. / 1-1/2″ Diam.
Air Flow:	119.3 per motor
Water Lift:	180″
Motor Type:	Lamb 923
Noise Level:	OSHA Approved

55 Gallon 55 G00 Turbine-Twin

Capacity:	55 gal.
Turbines:	2
RPM:	22470
AMPS:	17
Volts:	120
Cycle:	60
Construction:	18-Gauge Steel
Warranty:	1 year
Hose:	Two 15ft. / 1-1/2″ Diam.
Air Flow:	119.3 per motor
Water Lift:	180″
Motor Type:	Lamb 923
Noise Level:	OSHA Approved

Circuiteer Max

Portable & lightweight yet heavy-duty
10′ hose
2 different size Blower Tips
Two Filters
120 Volts 18.5 Amps
120 Volt Outlet for Clippers
Choice of one motor for delicate jobs or two motors for more blowing power.
Ideal for blowing leaves from your yard, debris off your walk or driveway, cleaning equipment, shops and barns.
Excellent for personal blow-off stations in all types of industry because it’s not compressed air.
Perfect for drying water spots off automobiles and motorcycles.
Cuts your dry time in half to speed up your grooming time.

Circuiteer II

Portable & lightweight yet heavy-duty
15′ Hose Blower Tip & Filter
Choice of one motor for sensitive areas or two motors for more blowing power.
120 Volts 17 Amps
120 Volt utility outlet for clippers
May be suspended, set on ground, or carried with adjustable shoulder strap.
Ideal for grooming your animals or as a blower for cleanup around the barn & house.
Excellent for cleaning industrial, personnel and work areas because it is not compressed air.
Prevents water spots
CSA approved by request
Two-year warranty

Circuiteer I

Portable & lightweight
May be suspended, set on the ground, or carried with adjustable shoulder strap or handle.
120 Volts 14.85 Amps
120 Volt utility outlet for clippers
CSA approved by request
Excellent for all types of blowing & drying.
Use one or two motors to vary pressure.
Available in a variety of colors
18 gauge steel body

Mini-Circ

Portable & lightweight
18 gauge steel body
CSA approved by request
Powered by lamb motor
An excellent blower/dryer for shows because of easy transport
9.5 Amp
Available in a variety of colors
The perfect blower/dryer for people just starting out grooming
Blow dry water spots off your automobiles and motorcycles

Stall mats and now trailer mats are at Barn World

Posted on February 24, 2011 by Rob

Use these great rubber mats for all kinds of uses

Barn World now carries stall mats and horse trailer mats.

Horse Stall Mats

The horse stall mats are long lasting, easy cleaning, non-absorbent and slip-resistant. They promote equine health and can save a tremendous amount in bedding costs. They’re easy to install and will fit standard stall sizes.

Barn World also offers custom cut mats and interlocking mat kits of 10’x10′, 10’x12′ and 12’x12′, pre-cut, interlocking and ready to go!

They are covered by a generous 15 year manufacturer’s warranty.

Some of the great features of these stall mats include:

Maintenance free stall floor – no more puddles.
Daily clean-ups are a breeze.
Less bedding, less work – smaller manure pile.
A must on concrete and asphalt floors.
Resilient – cushions horse’s joints and muscles.
Insulates resting animal against cold and damp.
Provides sure footing even when wet .
Button top mats are ideal for foaling stalls.

This is the thickest, toughest and most economical stall mat you can buy!

Horse Trailer Mats

SureHoof Horse Trailer Mats – Long Lasting, Easy to Clean, Non-Absorbent, Protects both Horse & Trailer.
Provides Sure Footing on Ramp & Floor. Versatile, durable rubber mats that can be used anywhere.

Protects trailer floors and ramps
Sure footing for your horse
Solid 1/2″ rubber
Factory cut to fit most trailers
Doesn’t bunch up or curl
Cushions and insulates
Lifetime OEM trailer manufacturer warranty –

No wonder it’s the choice of leading trailer manufacturers!

This trailer mat is also protected and guaranteed with a 15 year manufacturer’s warranty!!

Hoof Stands are at Barn World for your farrier hoof stand needs!

Posted on February 24, 2011 by Rob

The HOOF-it® ‘All in One’ Hoof Stand

Hoof care the easy & comfortable way! Easy on the horse and the user, the Hoof-it® Stand gives you both the post and cradle integrated into one, innovative hoof stand. Do yourself a favor! Take the pain out of your back and knees with the New Hoof Stand from HOOF-it® Technologies

The HOOF-it® ‘All in One’ Hoof Stand, designed by Farrier Steve Samet, features a shock absorbing, integrated rubber cradle and hoof post into one easy to use unit.

The Hoof Stand provides a stable and safe support for the horse, allowing it to relax without putting all of it’s weight on you.

For additional safety and stability when working with the Hoof-it®Stand try the following:
* keep on foot on the base unit when working with the Hoof® Stand
* do not leave the horses leg or hoof in the cradle or on the stand, when unattended.

Benefits for Farrier’s, Veterinarians and horse Owners who use the HOOF-it® Hoof Stand:

√ Easy to use “All in One” innovative, design integrates both the post and cradle in to one.

√ The innovative design of the HOOF-it® Hoof Stand dramatically reduces your risk of getting injured during hoof care tasks.

√ The HOOF-it Stand is ideally suited for use with all types of horses, including older horses that require special support and comfort during hoof care tasks.

√ The rubber cushioned Cradle fits different hoof sizes and hugs the hoof.

Let HOOF-it® Hoof Stand deal with the majority of the horses weight during any type of hoof care tasks, rather than your back or knees.

Visit www.BarnWorld.com today to see all of Barn World’s farrier supplies and livestock supplies.

Mini feed bins hold more than just grain

Posted on February 18, 2011 by Rob

Feed bins from Barn World

These feed bins are ideal for use as feed bins, storing corn for burning stoves, various grain pellets, bulk seed, or anything you need saved and easily dispensed. They come with a hopper collar and slide valve for easy dispensing.

Mini Feed Bins from Barn World offer hobby farmers a great feed bin storage option.

Small Feed Bin Details

With the increasing popularity of corn-burning stoves, the mini bin offers a solution for storing the corn needed to burn those stoves
Ideal as a feed bin for small hobby farms
Works well for range cubes – approx. 3/4″ round and 2″ long
Feed bin has a 40 bushel or 2,240 lbs capacity
Protects feed from moisture and bugs
Feed bin is constructed of galvanized steel
Load feed through the lid on top of the bin
This mini feed bin weighs 211 Lbs.
5′ diameter, 8′ tall

Visit Barn World today or call anytime for help with your storage needs! (720) 238-2190