Cattle Guards can be dangerous to some animals.

Barn world
Buy Cattle Guards at Barn World

 

Cattle guards can be dangerous to some animals.

Although they may be the most efficient means of keeping livestock in without a gate, we don’t recommend them for all animals.

When Gates are the Best Option

Horses, may be be most at risk and when attempting to cross a guard.  The anatomy of a horses’ leg are such that they may slip down between the pipes forming the top of the guard and in to the vault area underneath.  This.will expose the weakest part of their legs to breakage, and once panicked, they can break it quite easily while struggling to get out. For their safety, we only recommend the use of gates with horses.

Goats and dogs are immune to cattle guards.   These sure-footed animals can simply walk with ease across the top of the pipes. Again, gates are the best option for containment.

Deer Guards

Deer are extremely athletic creatures.  Their ability to jump seems almost effortless as they cross large distances in graceful hops.  It becomes necessary to extend the distance of the guard in the direction of travel to deter these animals from attempting cross.  A common white tail or mule deer can easily jump an 8 foot distance without any effort at all.  These animals require a better deterrent than a cow and and by combining and bolting together two guards, the effective crossing area becomes too daunting even for these creatures.  We recommend at least 16 feet in the direction of the vehicle travel to dissuade even the most ambitious jumpers.

When considering barriers for deer, it is important to remember that not only can they jump across large distances, but they can also jump over tall fence lines.  This will require that the fence line be extended directly to the edge of the cattle guard.  With bovine, a set of wings prevent crossings on the shoulders of the roadway, but with deer, a tall fence right to the shoulder will required.  You want to prevent jumping across the ends of the fencing.

Cattle Guards are for Bovine

The best use for these barriers is of course with cattle.  The traditional round pipe guard has been found to be more effective than the flat top.  Flat top finishes allow for smoother vehicle crossings, but the best for livestock have rounded tops.

Part of the effectiveness is a visual trick played on the cattle’s depth perception.  The shadows created by the round pipe make the crossing look even daunting than it actually is.  This in turn creates an even larger mental barrier and dissuades most livestock from even considering a crossing.  There are the occasional large bulls that when properly motivated can attempt a 6 foot or sometimes even an 8 foot jump, but these are few and far between.  When properly installed with wings, almost all cattle will refrain from even attempting a crossing.

Although designed almost exclusively for cattle, these barriers may be also be used for deer, when properly installed.

ATV Cattle Guard

ATV Cattle Guard

New this year is the ATV guard.  Designed for ease of installation, this porable standalone is a great option for fence line crossings for off-road vehicles in remote areas.  We have even custom designed these for golf cart crossings of fence lines.  Simply make a cut in your fence and drop into place.  It couldn’t be easier to install and the built-in rise creates an extremely effective optical and physical barrier.

Barn World offers plenty of assistance

If you have any questions about your cattle guard project, or need any help at all, please don’t hesitate to contact Barn World when planning your installation.  We have a wide variety and can offer quotes and bids for any project.

Barn World, LLC
720.238.2190

 

 

Heavy Duty Cattle Guards, a Texas Fence from Barn World

Barn World Logo

Cattle Guards

Barn World offers several types of cattle guards for private, commercial, public highway and heavy duty offroad equipment use. We comply with city, county, and/or state regulations.

Whether it’s called a Texas gate or a cattle guard, Barn World has the variety and selection needed to complete your project.

Private Use Cattle Guards

Private use cattle guards are perfect for farm and ranch use and for access areas where the total axle weight is up to 10 tons.  Semi trailers, tractors and large farming equipment are perfect for this type of guard.

Boxed style cattle guards  are designed to sit on flat ground. Gravel underlayment is recommended for drainage of these cattle guards. In many cases these boxed cattle guards are used for wheel washes in construction sites.

Flat style cattle guards are designed to be mounted on cement footings.

 

All cattle guards can withstand the weight of full tractor-trailer loads.
These cattle guards are constructed with an approximate gap of 4″ between each pipe.
Due to availability of pipe, cattle guards will be built with either 9 pieces of 4 1/2″ outside diameter pipe, or 11 pieces of 3 1/2″ outside diameter pipe and are 12-1/2″ tall.
There is no difference in strength between the boxed cattle guard and the flat styles of cattle guards.
These cattle guards are designed to accommodate full semi loads at 10 tons per axle.
Cattle guards weigh about 100 Lbs. per foot (a 10′ cattle guard weighs about 1,000 Lbs.). Add approximately 8 Lbs. per foot for boxed cattle guards and about another 200 Lbs. total for winged cattle guards.
To use for deer, you may need to place two cattle guards in tandem so you have 16 feet of protection. Cattle guards are easily bolted together and the extra depth will deter deer.
For a shipping quote, please send us an email with your destination zip code and quanitity or feel free to call the telephone number at the bottom of this page with any questions you may have about our cattle guards.
If you prefer, you may order your cattle guards online without the shipping total and we will forward the exact shipping cost for your review via email before processing your order.
A very important note: You must have equipment available to unload the cattle guards from the delivery vehicle when it arrives. The delivery truck will require you to unload the cattle guard with a loader or fork lift or some other means upon delivery.
Private use cattle guards are NOT built to exact dimensions and sizes may vary slightly.  Adding the removable box option will add about 7″ to the total length and width of the cattle guard. For example, a 12 foot cattle guard will be about 12′-7″.

Also see our unique ATV Cattle Guard:

For more information on cattle guards, installation or for help with any of your livestock supply needs, please visit www.BarnWorld.com today or call (720) 238-2190 and we’ll be happy to help.

Remember, Barn World is y our home for everything from saddle pads, hay feeders, grain bins, mineral feeders and everything to do with livestock.  We even carry livestock scales!

Horse hay feeder from Hay Hut – A great horse round bale feeder!

Barn WorldBarn World now carries the Hay Hut hay feeder!

 As the entire country is affected by the drought, the cost of feeding your livestock continues to rise.  It’s now more important then ever to minimize waste from feeding.

Barn World carries a large selection of hay feeders to minimize waste and provide increase profits.  The Hay Hut hay feeder is a great horse hay feeder that is so easy to use and simple in design that feeding round bales to your animals is a cinch.

Horse Hay Feeder

In addition to the actual hay/cost savings, the use of large bale hay significantly reduces Labor costs and these Hayhuts help to minimise pasture stress in overstock situations and during poor forage growing conditions.

It is interesting to note how well these units stop ‘big bale bickering’ and also how they bring a strong air of calmness and contentedness across the ranch as the horses all know that they have a constant source of forage.

The unit ships in two halves with simple build instructions and takes approximately 30 minutes to bolt together. They are very easy to move, manage, load and maintain

The Hayhut is a robust, durable, and UV stabilized covered hay feeder made of polyethylene and hence it cannot rust and does not require any maintenance unlike the majority of metal feeders.

 

The Hayhut is a full 84 inches in depth so that it can accommodate the largest of round rolls now being produced in the USA and up to twenty conventional square bales or the majority of big square bales. This additional depth also allows it to be easily pushed back over very large bales, even if they have been placed on a pallet, without catching the top lip of the feeder on the bale.

It is 84 inches high so that there is plenty of headroom for the use of a pallet while still allowing for good airflow and cooling over the top of the bale.

Hayhut will fit in the back of pickup. The width of 72 inches allows up to three units (in six halves) to be transported easily in a standard bed pick-up truck (see photo).

The Hayhut is delivered in halves to reduce shipping costs and a single half unit can be ordered. A half unit can be mounted against a wall or hard structure for use with conventional square bales. It can also be mounted against a fence with a locally purchased plywood back attached for weather protection

This half unit measures 42″ x 72″ x 84″ and has four feeding windows.

The unit ships in two halves with simple build instructions and takes approximately 30 minutes to bolt together. They are very easy to move, manage, load and maintain and we have many testimonials to that effect. The Hayhut is supplied with all assembly hardware and a lifting eye for relocation purposes. It can also be relocated with a round roll by inserting the roll inside the unit. Just see our video to see how easy it is to move.

Hayhuts are warranted for 1 year. Similar units of identical material from the same manufacturer have been examined after 6 years of 24/7 use in Missouri and this leads us to believe that Hayhuts should provide at least 10 years of good service which is an outstanding return on investment.They are designed and manufactured to accommodate all sizes of round rolls up to 1600 lbs. We have incorporated bigger windows for larger horses up to 17hh and anchor points for windy conditions.

Here’s a great demonstration video:

http://youtu.be/G8rjnBk1wh4

Below are just some of the happy customers we have using Hayhuts. 
Please contact us for more information or if you wish to provide a testimonial about how Hayhut hay feeders work for you.

Gottado Ranch, Ocala – April 2011
We purchased 2 Hay Huts at an equine event in Ocala, FL. They are easy to set up and use. As soon as we had them in the field the horses came over to check it out. They were eating out of it before we left. We had a really bad rainstorm about 3 days after we started using our Hay Huts. I went out after the storm to check the hay inside the huts. The hay was bone dry! The wind did not even blow rain in the windows. The horses love it and none of them fight. There is no manure or urine in the hay because the Hay Hut prevents this. This results in almost all of the hay in the Hay Hut is being used as food rather than bedding. Thank you Hay Hut for a great product that saves time and money. We plan on purchasing another Hay Hut before next winter.

January 2011
Thank you so much
for your courtesy and help as I decided whether or not to buy your Hayhuts product, for Potomac Glen Riding School . Since we have four paddocks at Potomac Glen, each containing 5 to 7 horses, we needed at least four Hayhuts, and I was initially very concerned about what I thought might be an expensive investment.

I am very pleased 
to report that the four Hayhuts I purchased have exceeded my wildest hopes of better hay usage & economy. Without a doubt, the Hayhuts have halved my round bale usage in just the last few months, thereby cutting my hay costs substantially. The Hayhuts have eliminated hay waste by keeping the horses from sleeping & defecating on the round bale hay. They also keep the ice, snow and rain off the round bales so I no longer lose a lot of hay. The Hayhuts have also eliminated the typical wasted mound of unusable hay, and the horses eat all of the round bale hay and leave only dust. My quality if life has improved because, in addition to saving on my round bale hay costs, I have also cut my work load substantially by feeding the bales to my horses only once a week, instead of two times a week, and the paddock clean up is virtually non-existent! Thank you again for your Hayhuts. When finances permit, I will be adding two more Hayhuts to the riding school. I will be happy to talk to anyone who is interested in Hayhuts. They can contact me at (301)601-0622, or our website is www.potomacglenridingschool.com. I will be happy to tell them about my experiences and to heartily recommend Hayhuts!
Susan Hansen Potomac Glen Riding School 24201 Clarksburg Road Clarksburg , MD 20871 2.

January 2011
Eliminates almost all waste!
Just a note to tell you I don’t think you were totally truthful with me when we talked about the hay hut: you said I could probably reduce hay waste by about 30%… well I have now fed two round bales out of the hut and am COMPLETELY CONVINCED waste is almost totally non existent! I watch the horses eat every day at some time or other and it seems when they do drag a mouthful out of the hut and drop it, that before they stick their heads back in they almost always pick up what they have dropped and eat it first. If there is a mouthful laying on the ground when they first walk up to the hut they usually pick it up and eat it first! They have developed really good “table” manners. I would bet out of the two bales fed so far, not even three (YES 3!) pounds of hay has been wasted and when it has snowed it was totally protected. The price initially, did seem high but with the price of hay it will pay for itself in very short order, well worth the investment for sure! Thanks for delivering and helping me get started assembling it and Thanks for a GREAT product!

AUGUST 21st 2010
The Hay Hut is really working out well!
The horses love it. Little to no waste on the hay. The hay stays dry, and no fussing. We did learn to set the hay on end instead of the side, as on the side they were able to peal layers off and out. Not so when it’s sitting on end. Carole (Missouri)

MAY 1st 2010
I just wanted to tell you that I put up 2 huts in my fields for my 5 horses and the 2 round bales lasted 3 weeks! I was feeding 4 bales of hay/day and at $4-$5/bale/day, that was about $16-$20/day. With the Hayhuts I am only spending about $4/day! I love them! Thanks, Kelly Melberg Winlock, Wa

A letter from Pennsylvania

We wanted to drop you a note and let you know how satisfied we are with your product. We purchased three units from you in July ’09. The units were assembled and put in the pastures once we received them. We started feeding hay on and off from October until December. Starting in December we began feeding fulltime from the feeders.

Our hay usage has shown a dramatic decrease. We do not see the large hay/manure piles that we routinely had using conventional round bale feeders. By this time each winter I am usually looking for sources of hay; our barn still has enough to last us for another two months. We have the largest number of horses that we ever have had on the farm, we have used less hay than we used to with fewer animals. We have fed small square bales, large round bales and large square bales in the feeders: they handle all of these varieties without any problems at all.

We are feeding animals in a variety of sizes and breeds. They all readily use the feeders without any problems. We are feeding our foals, yearlings, broodmares, miniature donkeys and a large Thoroughbred and Irish Sport horse on these feeders. We have three pastures running at the present time, one feeder has five horses on it, one has ten broodmares and the other has six geldings and two donkeys.

Assembly of the units was easy and took only around 20 minutes per hut. The green color blends in well with our fields and makes the huts easy to find in snow drifts, lol. Ordering and delivery were easy and I believe we will easily recover the cost of the units by the end of this year or the beginning of next. The amount of hay saved and a decrease in wasted hay/manure mixed is unbelievable.

We would highly recommend your product to anyone feeding horses round bales of hay or even small bales. The quality of the huts, the cost, the performance and your customer service have made purchasing and using these units a pleasure.

Thank you, The Hillards Pat and Kathy Hillard

City of Houston Mounted Patrol
Hayhuts are everything they say they are and more. We’ve had 4 Hayhuts for over 5 months now and have already recognized a savings with less waste. All 38 Police Horses love the Hayhuts as there is always fresh clean hay available to them when they are turned out. There is no fighting over the hay and no injuries caused by the Hayhuts. We have all sizes and breeds of horses at the Houston Mounted Patrol and all of them love the Hayhuts. Hayhuts prove the simplest designs are usually the best. Our horses thank you for making such a great product!” – Sgt. Leslie Wills, Houston Mounted Patrol

Road to the Horse Chris Cox uses Hayhut Hayhuts save and preserve the hay. They keep the hay weather protected and are horse friendly.” – Chris Cox

Nebraska Blizzard
Hay Feeders for Horses
Hi Denis, Just thought I’d let you know the Hayhuts made it through their first Nebraska blizzard just fine! I thought I may find them either full of snow or blown across my feeding area, but, neither was the case. They stayed in place, no snow was inside and the horses had plenty to eat all through the storm! – Mary Anne G. – Nebraska From using one round bale every 3-3 1/2 days to every 5-5 1/2 days I have been using the amazing Hayhuts for not quite a year now. I was about done with round bales before I found these. The horses would waste so much. We had one paddock where we were feeding 1 round bale every 3 to 3 1/2 days. When we started using the Hayhut it went to 5, 5 1/2 days sometimes even 6 days. I am now using 1/2 a Hayhut in a shed and another on the fence line. We throw small square bales or flakes of hay. There is no waste doing that. When you feed alfalfa to the babies they do not stand on it any more. They love their hay hut. If you ever use one you will not let it go. What a great invention.
– Karen Bruce, Irish Oaks Farm

The mini can eat there too
“Well it’s been a week and I LOVE it. Loads of rain and all the hay dry. The mini can eat there too, if I put hay high or just put bale under opening. Another satisfied customer. Thanks!” – Vicki – Florida

 

Be sure to feed smart this summer and receive the economical benefits and ease of use the Horse Hut Hay Feeder offers.

Also visit Barn World today for all of your livestock supplies needs.  We also carry a large selection of cattle guards, hay feeders, grain bins and even 5 Star saddle pads.

Stock Tanks help weather the drought.

 

barn world logo

Stock Tanks and Livestock Waterers –  Weathering the Drought

This summer has already seen the worst drought conditions since 1988.  More than 1,000 counties in 26 states are classified as natural disaster areas.  Since July 10th, 60 per cent of the lower 48 states were in drought conditions.  This includes states from South Carolina to Nevada and is the most land affected since the US Drought Monitor began keeping records 12 years ago.

These conditions require that your livestock, horses, hogs and other animals have a fresh supply of water constantly.  The high temperatures will dehydrate and negatively affect your animals health.

Barn World carries a large selection and supply of galvanized stock tanks, livestock waterers and waterers to ensure healthy animals.

Our hog waterer and pig waterer provide a constant supply of water for your animals and come in 35 and 80 gallon sizes.

Features of the hog and pig waterers:

  • Made of 100% non-porous polyethylene will not rust, rot or corrode.
  • Confinement pen acids have no effect waterers last and last.
  • Quick and easy cleaning no pans or shields to remove from drinker trough.
  • Big hogs drink with ease from 18 inches wide x 17 inches high x 9 inch deep drinkers.
  • Trough height from floor is 6″, so little pigs drink easily.
  • No cracks, corners or crevices to collect sediment or bacteria.
  • Each drinker has a drain plug, so washing and flushing is fast, simple and complete.
  • One dependable float and valve handles both drinkers.
  • Heavy steel-plated chew guard protects trough lip.
  • Gallon capacity calibrations molded into tank wall.
  • Float and valve completely protected from hogs.
  • Manual fill
  • 41 lbs.

We also carry livestock waterers to be used as cattle waterers and horse waterers.  They come as small as 4 gallons and as large as 110 gallons.

     

Barn World livestock supply also carries equine tack waterers for use in the stall.

stall waterer for equine

  • For use in single horse stall.
  • Smooth rounded edges for safety.
  • Durable 100% polyethylene construction; urethane foam insulation.
  • Easy valve access; one-screw, quick water level adjustment.
  • Minimum intrusion on stall space.
  • Four-bolt installation.
  • Plumb from above or below.
  • Ample drinking space; plentiful water supply with minimal waste.
  • Large easy drain; no disassembly required.
  • Attractive design; five color options.
  • Stainless steel anchor bolts included.

Barn World also carries poly stock tanks, great for livestock, kids swimming pools and adult soakers!  These tanks come in as large 9′ diameter and are great for cooling off from the summer sun.

plastic stock tank

Our weather resistant, multipurpose wading pool lasts year after year.
Features:

  • The ultimate wading pool – perfect for summer afternoon wading, splashing, and cool relaxing fun.
  • Sidewall are only 24″ high, so kids (of all ages) just step in.
  • Tough pools made for heavy use.
  • 6′ diameter pool holds 335 gallons of water.
  • Both are big pools for big family fun.
And for the herds, we carry the bottomless stock tanks, from 2,668 gallons up to 11,486 gallons.  These large livestock tanks are a great addition for keeping a large herd of animals hydrated throughout the summer.
bottomless stock tank

Keep cool this summer with our large selection of livestock tanks and wading pools.  Visit www.BarnWorld.com today or call (720) 238.2190 for all your cattle guard, hay feeder and livestock supply needs.

 

 

 

Cattle Guard article from Working Ranch for Barn World

Love That New Cattleguard

– by Jennifer Showalter, Working RanchTV

cattle guard

Handling Equipment Powder River cattleguards are designed to meet the American Association of State Highway Transportation Officials (AASHTO) specifications. The strongest models are built to handle up to 30 tons per axle. Opening and closing a gate from time to time is no sweat off any rancher’s back. It’s when the same gate has to be gone through over and over that it becomes more trouble than it’s worth. With this in mind, every rancher has a cow or two that seems to be able to smell an open gate and won’t let anyone slide by without closing the gate each and every time. To ease the aggravation and time loss with these high usage areas, ranchers are relying more and more on cattleguards. Matt Johnson with Powder River Livestock Handling Equipment in Provo, UT points out, “Cattleguards are the ultimate gate replacement for high traffic areas, but placing a guard in an area that you access only occasionally or that is less critical for gate control is probably a waste of resources.” To help with the selection and installation of a cattleguard, Working Ranch went out and gathered some pointers from a few different manufacturers. This is what we found:

Picking the right one: When selecting a cattleguard there are a number of things to scratch the old noggin over. For starters, rancher must determine what is the heaviest and the widest pieces of equipment that will ever cross their cattleguard. They then have to look for the cattleguard that will meet those standards.

Quality materials and craftsmanship obviously influence the price of a cattleguard, but also determine its longevity as long as the proper load rating is not abused. “The higher the cattleguard (load) rating, the higher the cost. The U-rated guards that are designed for extremely heavy loads are the most expensive. Anytime the distance across a road exceeds 16’, shipping rates can rise dramatically. In terms of cost, it sometimes makes more sense to order two small cattleguards to bolt together in either direction than it does to order one large custom cattleguard,” says Robert Moore with Barn World, LLC in Parker, CO. Ranchers must decide if a flat or box type cattleguard works better in their environment and whether they prefer square or round rungs. Flat style cattleguards are placed over a dug out cement vault, whereas box style cattleguards basically have a built in vault and sit close to the top of the ground.

Placement: Cattleguard placement varies because of different soil conditions, climates, drainage, and intended uses. Barn World suggests ranchers have a local contractor, who is familiar with the area, set the more permanent types of cattleguards. Installation for these cattleguards typically involves digging a one foot deep trench that is one foot wider than the cattleguard. Six inch wide walls should then be poured around all four sides to prevent dirt from collapsing in. In the bottom of the trench, a 12” wide and 18” deep footer is needed under each beam of the cattleguard. It is critical that the cattleguard sits on footers that are sufficient to support the full load of traffic. Ranchers must keep in mind that the vault does not support a cattleguard in any way. While setting a cattleguard, installing large PVC pipe through the forms or digging out and adding gravel will help with drainage issues. Box cattleguards typically do not need a vault. Their box formation keeps dirt from working into the guard. “One of the biggest mistakes folks make is setting their (box style) cattleguard at ground level. You have to hold them slightly above grade and ramp up to and away from them to prevent them from filling in.

Cows don’t like to jump on a grade where their front-ends are higher than their back-ends,” explains Tom Jones, with JE Hill Precast in Leesburg, FL. When placing two cattleguards next to each other, both gaps and edges must be avoided. If there is a solid edge, cattle can master walking it. Some ranchers find it beneficial to purchase or build a set of wings for their cattleguard. “Various styles of wings can be used. They should be able to be secured to the guard grid or the base it is built on. Any type of wing should remove the risk that livestock can circumvent the guard,” notes Johnson. Jones points out another added benefit of wings, “Wings are a way of exaggerating the opening of a cattleguard. For example, if you have a 16’ cattleguard and a 16’ mower, you can lay the wings back and fit through.”

Limitations: Jones warns people that before they are sold on the idea of a cattleguard, they must be aware of their limitations. He finds that cattleguards typically do not work to separate cows from their calves or cycling cows from bulls. They also have a hard time holding cows without water from water and cows without feed from feed. Jones discourages ranchers from putting cattleguards in corners or along the edge of an alleyway where cattle can easily crowd them.

A peek at what these boys have to offer: Powder River: www.powderriver.com Powder River cattleguards are made out of structural steel, have square cross rails, and are either powder coated green or painted yellow. These cattleguards are designed to meet the American Association of State Highway Transportation Officials (AASHTO) specifications. Powder River builds a wide range of cattle guards with the strongest built to handle up to 30 tons per axle. Powder River cattleguards are available in 8’, 10’, 12’ and 14’ road lengths and 7’5’’ and 8’ widths. Powder River offers an optional three rail clean out section on all of their models except the U-80’s. Wings, steel posts, and pre-cast concrete bases are also available. Powder River stands behind its cattleguards with a five-year warranty.

Barn World: www.barnworld.com Barn World offers rated, standard, and basic boxed and flat style cattleguards.

cattle guards

Their rated cattleguards are intended for highways or for heavy off-road equipment. They are available with certified load ratings of H-15, H-20, U-54, and U-80. Barn World also offers an HS20 rated cattleguard to meet State and Federal requirements. Certified structural steel is used in the manufacture of all Barn World HS20 rated cattleguards. Barn World’s line of standard cattleguards are made with new .113 walled steel pipe, and like all Barn World cattleguards, come with a gray enamel finish. Their basic cattleguards are made of a heavy duty structural .188 walled pipe with diameters of 3.5” or 4.5”.

Barn World now offers a cattleguard design specifically for ATVs. These ATV cattleguards are made of 1.5 x 11 gauge square tubing and are 72” wide by 91” long. The overall width of these guards including their wings is 87”. A 14” ramp on each side allows them to be set on top of the ground and eliminates the need for a vault. Barn World is strictly an Internet-based business.

With three cattleguard manufacturing plants across the United States, Barn World strives to keep shipping costs at a minimum. JE Hill Precast: www.jehillprecast.com JE Hill Precast concrete cattleguards feature rounded top rails and built-in footers that eliminate the need to pour concrete. These cattle guards simply sit on top of the ground and are best positioned so they are held slightly above grade with a gravel ramp on both sides. They come in 12’, 14’, and 16’ road spans and all measure 6’6’’ across. JE Hill Precast’s standard cattleguards have a 72,000 pound gross vehicle weight (GVW) limit, while the heavy duty models have greater than a 90,000 pound GVW limit. These cattleguards weigh from 5,000 to 7,000 pounds depending on their size. JE Hill Precast cattleguards are designed so they require no additional construction, can be installed in two hours or less, and can easily be relocated.

Grain Bins: Barn World now offers plastic grain bins

Barn World Logo

Grain Bins from Barn World

Barn World now carries a large selection of Poly Grain Bins.

Poly Grain Bins are a fantastic feed bin design and are perfect for handling highmoisture soybeans, corn and granular materials. These feed bins are a polyethylene grain bin constructed with a high-density polyethylene they won’t corrode or rust. and will always be attractive and clean. 

The interior surface is a very smooth two-piece construction that reduces bridging.  There are no rivets and grain-clogging seams to contend with. The translucent polyethylene allows you to visually check material line from the outside.

All of our plastic grain bins have a 22″ top opening with a hinged, vented filler cap and a pull rope that allows ground control for filling.

There are 3 different transition collars available for the slide valves– 90°, 45°, and 30° angles. (See Accessories on page 18.) The new style collar allows easier attachment to the bottom cone with little or no cutting necessary. Our slides feature a galvanized plate and guide system. Our auger boots will attach to any of our slide valves and handle 4″ or 6″ augers. The auger boots have a clean out access cover.

The poly grain bins have a 16″ hole in the bottom cone and come in a variety of sizes:

  • The .8 ton bin has 38″ of ground clearance to the slide valve.
  • The 1.5, 2.5, and 3.5 ton bins have 15″ ground clearance under the slide valves.
  • The 4.5, 6.5, and 8.5 ton bins have 14″ ground clearance under the 90° slide valve; and 11″ ground clearance under the 30° slide.

Theses bulk feed bins feature heavy-duty support frames with extra large secure plates for more holding power. They have flat strap cross bracing for increased stability. The .5 – 3.5 ton units come standard with 4 legs; the 4.5 thru 8.5 ton units have 6 legs. The legs have large support tabs which can be bolted to concrete for added stability especially on the larger units.

 

grain bin picture

Polyethylene Grain Bins

All of the plastic grain bins at Barn World have a sturdy ladder with slip guard. It is braced securely to the top of the tank near the filler cap.

All hardware is supplied. Erection time is one-third of steel bins.

Frames have a baked-on polyester powder coat finish which resists corrosion.

It is recommended that you use a concrete pad at least 5 1/2″ thick for our 4.5 ton thru 8.5 ton units.

Please visit BarnWorld today and change out not only the bins, but the wide variety of farm supplies, ranch supplies, and equestrian supplies made by American manufacturers. Our best selling items are hay feeders, cattle guards, feed bins, saddle pads, mineral feeders, livestock scales and many livestock supplies.  (720) 238-2190

Farrier Supplies: Hoof Stands – Save your back, Barn World has a hoof stand for all sizes!

 

Barn WorldBarn World

 

Hoof Stands from Barn World

At Barn World, we’ve come across a lot of great products and one that has stood out  with it’s ability and ease of use is the Hoof-It hoof stand.  Whether working on a large draft horse hoof, a standard horse hoof  or small hoofed animals such as ponies, smaller horse breeds and older horses, there is a hoof stand available to make the back breaking chore of trimming a hoof much, much easier.

The HOOF-it®  Hoof Stand, designed by farrier Steve Samet, features a new modern design which integrates the post and cradle to create a “two-in-one” unit. This combo design allows the user to easily switch from the standard hoof cradle to the draft cradle in order to work on and shoe a wide range of hoof sizes.

The cradle and post are covered with a shock-absorbing rubber material that provides a comfortable support for the horse, while the wide base unit provides added stability and safety for the user.

The hoof stands are available in three sizes and in a combination stand:

Please check out the instructional hoof stand video below to see just how easy working on a hoof can be with the hoof stand.

Hoof Stands

The HOOF-it® ‘All in One’ Hoof Stand

Hoof care the easy & comfortable way! Easy on the horse and the user, the Hoof-it® Stand gives you both the post and cradle integrated into one, innovative hoof stand. Do yourself a favor! Take the pain out of your back and knees with the New Hoof Stand from HOOF-it® Technologies

The HOOF-it® ‘All in One’ Hoof Stand, designed by Farrier Steve Samet, features a shock absorbing, integrated rubber cradle and hoof post into one easy to use unit.

The Hoof Stand provides a stable and safe support for the horse, allowing it to relax without putting all of it’s weight on you.

For additional safety and stability when working with the Hoof-it®Stand try the following:

* keep on foot on the base unit when working with the Hoof® Stand

* do not leave the horses leg or hoof in the cradle or on the stand, when unattended.

Benefits for Farrier’s, Veterinarians and horse Owners who use the HOOF-it® Hoof Stand:

√ Easy to use “All in One” innovative, design integrates both the post and cradle in to one.

√ The innovative design of the HOOF-it® Hoof Stand dramatically reduces your risk of getting injured during hoof care tasks.

√ The HOOF-it Stand is ideally suited for use with all types of horses, including older horses that require special support and comfort during hoof care tasks.

√ The rubber cushioned Cradle fits different hoof sizes and hugs the hoof.

Let HOOF-it® Hoof Stand deal with the majority of the horses weight during any type of hoof care tasks, rather than your back or knees.

Visit www.BarnWorld.com today to see all of Barn World’s farrier supplies and livestock supplies.

 

 

Cattle Guards: A Cattle Guard for all your livestock control needs!!

BarnWorld.com

 

 Cattle Guards:  A Cattle Guard for all your livestock control needs!!

Barn World carries rated cattle guards for public highways and road construction project in addition to private property use cattle guards.

Rated Cattle Guards
Rated Cattle Guards are available in four different certified load ratings. These cattle guards are intended for use on public highways or for heavy off-road equipment.
The American Association of State Highway Transportation Officials (AASHTO) provides guidelines for cattle guards with maximum load ratings. AASHTO load ratings are suitable for all types of applications including heavy duty logging roads.

AASHTO Design Specifications

Our HS20 rated cattle guards are made from schedule 40 steel and come in a variety of sizes to fit various cattle guard projects. We can alter the design of our cattle guards to use different kinds of pipe and rail depending on your needs. We have used round pipe, square rail, I-beam and other types of rail and channel to make rated cattle guards that are suitable for all public crossings.

Barn World HS20 rated cattle guards conform to AASHTO load rating requirement by type of truck and maximum axle load. Our rated cattle guards come with an engineer’s stamp and are certified to meet the AASHTO load ratings so you can feel confident that you are getting the best quality cattle guard.

Barn World also carries economical cattle guards designed for private use:

Private Use Cattle Guards
It’s best to start with the load rating requirements for your project. Cattle guards come in several different rated and non-rated designs. For private driveway use, we recommend the basic cattle guard as the most economical option.

Basic cattle guards are a heavy duty structural .188 (3/16″) walled pipe with a diameter of 3.5″ or 4.5″ depending on availability or request. Note that the walls of the basic guards are thicker then schedule 40.

Standard cattle guards are another option for private driveway or ranch use. The standard cattle guards are made with new .113 walled steel pipe.

And to complete the cattle guard selection, we also offer a very versatile ATV Cattle Guard.

ATV Cattle Guard

Call Barn World with your questions and plans to get quotes on HS20 rated cattle guards at 720-238-2190.

 

Mineral Feeders and Mineral Licks – an important component to keeping your livestock healthy year-round

Here is a great article from Working Ranch about the importance of getting your livestock the minerals they need during the winter months. and the attention to the type of supplement quality and quantity.

Barn World’s carries a large selection of troughs and grain feeders to help keep your livestock healthy.

Barn World also carries a large selection of mineral feeders and mineral licks to help ensure the proper nutrients are a part of the diet.   A mineral feeder is an important part of facilitating the absorption of minerals.

From ground mineral feeders like the Dura Life to the wind vane style mineral feeders like the upright mineral feeder, Barn World has the tools to make sure your animals remain healthy all season long.

 

 

Make sure your cows are nutritionally ready

From Working Ranch

– by Gilda V. Bryant

– photo by Lucie Wiese


Minerals are important for herd health, reproduction and efficiency during winter. However, that is only part of the picture.  Extra protein and energy are vital during cold, wet weather.  Producers should also be aware of forage and by-product supplementation quality, as well as body condition scores.

“The challenge with minerals is there’s just no single answer,” says Rick Rasby, PhD, PAS (Professional Animal Scientist), Beef Extension Specialist, University of Nebraska (Lincoln).  “Think about minerals as part of a total diet those animals are eating.”

Rasby encourages producers to sample baled forages for moisture content, protein, energy and mineral profiles.  Once a producer knows his forage quality, he can adjust the mineral package for his herd.  He says, “Use the mineral as a supplement to bridge the deficiency gap in those forages that are being consumed.”

He also recommends that producers analyze samples of supplemental feed such as gin trash, cotton seed, or distiller’s grains.

Many regions with ethanol plants have distiller’s grains available for the cow/calf sector.  Rasby says, “It’s an excellent feed, works well with forages, and is high in protein, energy and phosphorus as well.”

Typically low in winter forages, phosphorus is a mineral that’s vital for bone and teeth development, and metabolic, neurological and cellular functions in cattle.  It’s also one of the most expensive minerals to supplement.  According to Rasby, reducing or omitting phosphorus from the mineral package when feeding distillers grains can save money.  Get advice from a nutritionist or beef extension specialist about adjusting nutrient values when feeding these supplemental rations.

In addition to minerals, protein and energy, utilizing body condition scores (BCS) is a management practice that cow/calf operators can implement on a regular basis. Scores range between one and nine with one being a very poor specimen and nine being obese.

Rasby adds, “Having mature cows in condition score five at calving not only has an impact on what happens at calving, but also on how quickly those cows are ready to rebreed after calving.  Those first-calf heifers probably need to be in a little bit better condition, say conditioning score six.

“Cows that breed early in the breeding season are in the right nutritional status.  Their calves are older at weaning and generate more dollars,” explains Rasby.

Is it right?

How can a cattleman determine if his mineral supplement and diet are on target? “Measure how they perform at calving,” replies Rasby.  “Are they good mothers?  Do they give enough milk? Does the calf perform well while it’s on its mother?  How quickly does the cow get ready to rebreed?”

Providing minerals is crucial to the Thomas Angus Ranch outside of Baker City, Oregon. Located in a valley between two mountain ranges, and flanked by sagebrush hills, owner Rob Thomas says, “We have long, fairly hard winters.”

He provides a custom mineral mix to his spring and fall calving herds, depending on forage analysis to fine-tune the supplement package.  Thomas says, “We increased levels of zinccopper, and selenium, the three minerals we’re deficient in.”

Beginning in November when snow is on the ground, he’ll feed alfalfa and grass hay.  He says, “We put up a lot of our own hay, so we feed what we put up.  We test our feed to see what minerals we need.”

As a result of their efforts he reports, “We have healthier cattle, better immune response, fewer treatments and a lower death loss.  We see increases in reproduction and gain and better feed utilization, which is important right now.  With extremely high feed prices, we want to utilize every bit of that feed, if possible.”

Across the country, Kevin Yon raises Angus cattle in the mild winters of west central South Carolina.  He provides three mineral mixes: summer, winter, and one for young growing livestock.  Yon says, “Our winter mineral program doesn’t differ drastically from our summer mineral program.  We include a higher level of magnesium to prevent grass tetany.  If all goes well we hope to have lush grazing on a limited basis, even in December and for sure in February and March.”

His winter diet includes stockpiled forages such as Fescue or Bermuda grass.  When possible, Yon likes to have rye grass or small-grain winter annuals on hand.  He explains, “It could be a combination of those and sometimes we’ll use a protein or energy supplement, which could be commodity by-products, such as whole cotton seed, dried distillers grains or corn gluten.”

He analyzes feed, grains and commodity by-products, seeking advice from a nutritionist to adjust his mineral program as needed.

“It’s important to have a year-round high-quality mineral program,” Yon advises. “That’s not always the cheapest bag of mineral, but it has the high levels that are needed for cattle in your area.  The cheapest bag is not always the best.”

Yon finds that his cattle have a more consistent consumption if he allows free choice at all times.  He says, “Know what the consumption rate should be and monitor that. In our part of the world, a covered mineral trough is important so the mineral doesn’t get wet, cake up and the cattle don’t eat it.

“As a producer, I see the benefit of minerals.” Yon explains, “The biggest for us is reproduction, cow herd efficiency, immune response, cattle health, and growth and development.  At our place we try to feed a cow as cheap as we can because 60-70 percent of our annual cost involves nutrition.  We don’t see that minerals are the place to skimp.”

Thomas also recommends feeding minerals, saying, “Do it based on science.  Go ahead and get a forage analysis based on what you’re feeding and do that every time you get a new batch of feed, so you know what you’re feeding and what minerals you need to add to the ration.”

Rasby says, “To be competitive, you’re really going to have to watch feed costs. How you put together feeding programs to meet your herd’s nutritional needs is going to be critical.”

To find a list of certified feed testing laboratories, check out: www.foragetesting.org.

 


PROTEIN AND ENERGY

“Minerals don’t do much if you’re not doing a good job of covering your water, energy, and protein needs for those cows,” advises Ken Bryan, PAS, and Ruminant Specialist with Cargill.  “A balanced diet is important because you have the added stress of environmental conditions like cold, wet weather, mud and wind, which are going to increase the cow’s nutritional requirements.”

Adequate amounts of energy and protein are critical during winter conditions. “If a cow will eat twenty-four pounds of dry matter in forage, she’s going to get all the energy she needs,” Bryan explains.  “If that rumen is functioning well, she’ll break down the fiber and utilize that feed.  That’s your energy source.”

Protein, a much-needed nutrient in cattle diets, is composed of true protein andnonprotein nitrogen.  Protein in forages will gradually decline, providing less protein as winter progresses, with a higher percentage of fiber.  “The nasty thing about fiber is a high fiber, low quality forage diet will restrict intake,” Bryan says.  “Now we’re going to supplement with a protein source.  The nice thing is, there are options for protein supplementation.”

“There’s the old standby, cake or range cubes, protein tubs or blocks and leftovers from oil seed products such as sunflower, cotton seed, or soybean meal and distillers grains from corn.  Look at the most economical way to deliver protein to the cow.”

Bryan cautions, “We’ve got to keep a minimum amount of fiber in that diet as we feed energy supplements.  We’re going to cause some long- term changes in that cow’s rumen… we’ll ruin her if we feed her like a feedlot steer.”

Cattle Guard informational site from Barn World: All your cattle guard questions answered!

BarnWorld.com

Barn World has created an informational site to help with your cattle guard selection.

Ordering a cattle guard has been made easy through our informational website at Cattle-Guards.com.  It takes the mystery out of selecting and installing cattle guards.

It covers types of cattle guards, cattle guard uses, cattle guard certification and cattle guard installation.

Also included is a cattle guard vehicle load table for cattle guard weight ratings and cattle guard load ratings.

Visit cattle-guards.com today to help with your selection and cattle guard installation.

Barn World offers several types of cattle guards to meet your specific needs.Barnworld’s HS20 Rated Cattle Guards meet the demanding specifications needed for State and Federal requirements such as DOT, BLM, USFS, NP, and US Military installations. These cattle guards will provide years of rugged service in commercial applications such as mining, forestry, agriculture, and petroleum production. They are also the cattle guard of choice for residential usage where city, county, or state regulations require the HS20 rating. Certified structural steel is used in the manufacture of all Barnworld HS20 rated Cattle Guards.

The economical Basic 6′ and 8′ wide cattle guards are a heavy duty construction made with 3.5″ or 4.5″ pipe depending on availablity. The Standard 6’and 8′ wide cattle guards are made of NEW 3″ Schedule 40 steel. All Flat Cattle Guards may be ordered with optional wings, integral box, or removable box. The ATV size guards are unique in the industry. These cattle guards are suitable for all types of projects on private land. The standard boxed cattle guards are perfectly suited to construction sites, mine sites and oil field applications.

Our 7.5′ and 8′ spec cattle guards meet current AASHTO load ratings and are suitable for all types of applications where a square pipe is desired including heavy duty logging roads. They may be ordered with optional wings or cleanout line.

Barn World has a cattle guard to meet your needs. Please call us with your questions and to obtain shipping quotes. We can also provide professional bid packages for large company, military, and government programs.

Visit BarnWorld.com for all of yourlivestock supplies and livestock equipment needs.